MR2OCNZ Gallery

<-- click on the club logo to return to the forum.


Fitting a S54 to a 1MZ


1MZ_and_S54_mating_28not_sexually_explicit29.jpg

Sorry far from complete I had camera issues (card got full) I have many other details to share such as which holes to drill, which to tap, where to have some welding done.....

19 files, last one added on May 23, 2013
Album viewed 2175 times

My 98 head gasket


well_theres_ya_problem.JPG

Car has done 4,000km's since these pictures were taken and still goes well, compression was at 185~190psi across the cylinders when checked at 1,000km's in after the reassembly.

6 files, last one added on Apr 19, 2012
Album viewed 38 times

New Brakes


Wow.JPG

Work in progress

2 files, last one added on May 03, 2012
Album viewed 32 times

Wairarapa Run 20-05-12


Tim_showed_up_with_my_dream_car.JPG

5 files, last one added on May 21, 2012
Album viewed 40 times

Wairarapa Wellington Manawatu Run 30-07-12


DSCF1466.JPG

12 files, last one added on Jul 29, 2012
Album viewed 270 times

V6 Transplant


engine_mount.jpg

1 files, last one added on May 23, 2013
Album viewed 23 times

6 albums on 1 page(s)

Random files - 98beamsmkII's Gallery
Clutch_Slave_Heat_Shield_Cut.jpg
118 viewsClutch slave cylinder heat shield neatly cut
Diff_Bolt_touches_Axle.jpg
104 viewsThe bolt from the motor to the diff side of the gearbox touches the axle!!!!!!
Low_profile_headed_bolt_-_problem_solved.jpg
109 viewsMade the head low profile, problem solved
Wow_look_at_the_dirt.jpg
52 viewsPretty dirty oil in there... Lucky there is no sludge! Those cams when I had them out I measured in Vee blocks in the mill at work with a DTI - 11mm lift on the intake!!!! 9.75mm on the exhaust. Mad mad lift wish I grabbed the profile too but didn't have time during my lunch break to set it up in a rotary table and take several hundred measurements.
Wow.JPG
Front Disc38 viewsLovely isn't it
Drill_through_and_die_grind_out_to_fit_a_M8_50mm_Cap_head_bolt.jpg
326 viewsYou need to drill through the bell house and grind it out so you can fit a M8 50mm long cap head bolt into the thread insert, use a ball headed carbide cutter!
The_point.JPG
To the point30 views
DSCF1440.JPG
Wood pidgeon hanging around while I eat my lunch at Ashurst Domain39 views
DSCF1451.JPG
Info sign in Ashurst Domain viewing platform46 views
DSCF1454.JPG
Ashurst Domain viewing platform lookout1103 views

Last additions - 98beamsmkII's Gallery
DSCF1824.JPG
Flywheel92 viewsCustom designed and machined locally flywheel, picture taken after shrink fitting of the ring gear.May 23, 2013
engine_mount.jpg
Driver side engine Mount37 viewsMilled the factory V6 mount flat so the MR2 mount plate can be bolted over it, next step is to weld angle iron in the right places so it can bolt to the factory MR2 mount.May 23, 2013
DSCF1466.JPG
Lineup at Pahiatua 55 viewsJul 29, 2012
DSCF1435.JPG
Lineup at Aokautere164 viewsJul 29, 2012
DSCF1433.JPG
Lineup at Aokautere264 viewsJul 29, 2012
DSCF1463.JPG
lineup on saddle road53 viewsJul 29, 2012
DSCF1460.JPG
wrapping around wind turbine's base49 viewsJul 29, 2012
DSCF1455.JPG
looking up at the turbine40 viewsJul 29, 2012
DSCF1454.JPG
Ashurst Domain viewing platform lookout1103 viewsJul 29, 2012
DSCF1451.JPG
Info sign in Ashurst Domain viewing platform46 viewsJul 29, 2012