2YODA 5sgte Build

[Benckj]

Manifold certainly looks like it will do the job. Time will tell with quality of flanges & welds.

On the FP use the stock hanger but be prepared to mod the pump mounts and wiring. Biggest restriction is in the hardline from tank to filter. I went with a larger AN supply from this point to filter to reduce head loss but also make easier to pull pump if required.

[Soleman]

Manifold certainly looks like it will do the job. Time will tell with quality of flanges & welds.

On the FP use the stock hanger but be prepared to mod the pump mounts and wiring. Biggest restriction is in the hardline from tank to filter. I went with a larger AN supply from this point to filter to reduce head loss but also make easier to pull pump if required.

I am wanting to change those lines for that reason, which is why i was wondering if people use pump hangers that are made with an fitting.

Soara manifolds are made for a wide range of applications and he is building a good name for himself.

[Soleman]

Sooooooo Little Update,

Engine is still at the machine shop.
partly my fault...

Purchased a D1 Racing 3sgte flywheel with intent.of running a single disc clutch but since been.convinced a twin disc setup is better for my build..

So i reached out to Barry at Mrp to make a Quartermaster 7.25 Clutch and flywheel setup for my desired power level.

Which has just been delivered to the shop so the rotating assembly can be balanced.



While this happens ive ordered a couple bearings for.my E153 so i can install my MFactory Lsd.

Sanding and Priming the engine bay for paint.

Intake Manifold is enroute from the Ukraine.

Have painted an Assembled 2 of 4 Blitz 03s.

and theres a Ton still left to do.

Full tune early.march is the goal so im good for toyota fest 2020 end of.march

[mknz]

Intake Manifold is enroute from the Ukraine.

Which one did you get?

[Soleman]

Intake Manifold is enroute from the Ukraine.

Which one did you get?

I got one made by Soara Performance. ita a straight runner but the manifold sita on the engine bay side then feeds into the boot.

meana i only have to cut two 3 inch holes instead of a big rectangle.

[Soleman]

So Motor is Back from Taylor Automotive,

Head is on and torqued down with the Arp 625+ Head Studs,

Gate Racing belt installed and the timing components.

i found the stock oil pickup and baffle lines up with the holes from the balancer off the 5sfe.

juat have to drill the holes out to m10 and it all bolts down. picture attached

[Soleman]

Motor is coming together, Just waiting on the intake manifold gasket so i can install the manifold. then the alternator can go on.

Need to order 1000cc injectors.
Spark Plugs.
Ecu
Turbo.
Coils

just a few things.

have a picture of the motor as it sits.

received_580541136026631.jpeg (133.75 KiB) Viewed 3922 times

[thorns]

WOW, looks amazing. Almost need a NSFW tag on that

[Soleman]

WOW, looks amazing. Almost need a NSFW tag on that

Haha Almost.

still a long way toooo gooo

[Alsw20]

Is there enough room on the firewall side of the engine for that manifold?

[Benckj]

Is there enough room on the firewall side of the engine for that manifold?

Was thinking the same. At very least the WG will need to be positioned somewhere else. It’s surprising how large they are.

[Soleman]

Itll Fit, will be tight. have test fitted the manifold on another car. the wastegate i have for it is a scarles one.and its too.wide so.it just hits the firewall, ill be switching to a turbo smart option.as they are skinnier

that will solve the problem.

ive also removed the factory deading and tin heat shields in favour of lava matt. so thatll save some room.

[Soleman]

Just a Couple of photo updates.

this lockdown is holding me up purchasing bc coilover, big brake kit. Can lambda for the ecu. other wise looking for start up in may

[Benckj]

Very impressive. Really had to shoe horn the engine into place.

[Soleman]

It slipped in easier then oem.